6x12 LuxeEdge Floor Register | 1 Inch Flange Steel Vent Cover - 6 x 12 - 1 Pack / Black
6x12 LuxeEdge Floor Register | 1 Inch Flange Steel Vent Cover - 6 x 12 - 1 Pack / Black
Estimated delivery : Friday, 30 October - Saturday, 07 November.
Couldn't load pickup availability
The 6x12 LuxeEdge Floor Register is our premium drop-in floor vent cover. Its 1 inch flange is the widest edge in the TRM range, so rough cuts, gaps and worn flooring around the duct opening disappear under a clean, flush, floor-matching frame. Drop it straight into your existing 6x12 floor duct opening, no tools or screws needed.
Made in Canada from 1.2mm (18 ga) Cold Rolled Steel with a durable textured black powder coat that stands up to daily foot traffic and will not crack or warp like plastic registers.
Key Features
- 1 inch wide flange covers more of the floor around the opening and hides uneven cut edges
- Drop-in installation fits standard 6x12 floor duct openings, no screws or tools required
- Same airflow as our Classic register with 24.3 sq in of net free area
- 1.2mm (18 ga) Cold Rolled Steel for long-lasting strength
- Textured black powder coat for a premium, finished look
- Built to order in Mississauga, Ontario
Sizing Note
"6x12" refers to the duct opening size, not the outer faceplate. The faceplate is larger to make room for the 1 inch flange. Always measure your existing duct hole before ordering.
Airflow Performance Data (6 x 12 LuxeEdge Floor)
Conservative engineering values.
Net free area 24.3 sq in • Area factor Ak 0.169 sq ft • Open area 34% of nominal
| Face Velocity (fpm) | Airflow (CFM) | Static Pressure (in. wg) | Throw 150 / 100 / 50 fpm (ft) |
|---|---|---|---|
| 400 | 67 | 0.01 | 3 / 6 / 11 |
| 600 | 101 | 0.03 | 5 / 8 / 16 |
| 800 | 135 | 0.06 | 6 / 11 / 22 |
| 1000 | 169 | 0.09 | 8 / 14 / 27 |
| 1200 | 202 | 0.13 | 9 / 17 / 32 |
| 1400 | 236 | 0.18 | 11 / 19 / 38 |
| 1600 | 270 | 0.24 | 13 / 22 / 43 |
Notes and Conditions
- Performance values are engineering calculations and estimates and are not yet laboratory certified. Certified ratings tested to ASHRAE 70-2006 and ADC 1062 will supersede this data once testing is complete.
- Airflow (CFM) is derived by continuity from the rated net free area at standard air density of 0.075 lb per cubic foot under isothermal conditions.
- The net free area shown is the conservative perimeter opening. Actual open area is greater, so delivered airflow meets or exceeds the listed values.
- Static pressure is a conservative calculated estimate referenced to the free-area velocity and carries an added margin. Tested values are expected to be lower.
- Throw values are estimates scaled to this product and are pending TRM ASHRAE 70 certification.
- Sound rating data is pending laboratory test.
- Dimensions are nominal and subject to manufacturing tolerance. Consult TRM Metal Products for applications beyond the conditions shown.
Disclaimer
This information is provided for general information only and is subject to change without notice. The values shown are preliminary engineering estimates, are not laboratory certified, and must not be used for code compliance, regulatory submission, or life safety system design until certified ratings are issued. Selection of the product and verification of its suitability for a given application are the responsibility of the system designer and purchaser. Installed performance varies with duct design, system static pressure, installation quality, and field conditions, all of which are outside the control of TRM Metal Products. To the fullest extent permitted by law, this data is provided as is, without warranty of any kind, express or implied, including any implied warranty of merchantability or fitness for a particular purpose, and TRM Metal Products assumes no liability for any loss, cost, or damage arising from its use or from reliance on it. All product names and trademarks are the property of their respective owners. TRM Metal Products is not responsible for typographical errors.
Shipping & Returns
Exclusive Offers
Secure Payments
100% Canadian made
Our products are proudly made in Canada to support our local economy and help create and keep jobs in our wonderful Country.
Since products are 100% made in Canada you can be assured that you will get products that are of high manufacturing standards and up to the expectations.
Excellent construction quality and fit & finish.
Looks great. Really high end feel.
